Goantifraud
Setting up Cisco 1760 for Synchronization with PBX and E1
Setting up Cisco 1760 for Synchronization with PBX and E1
27-Oct-2016 14:15

Setting up Cisco 1760 for Synchronization with PBX and E1

Most people ask the question if it is possible to set up Cisco 1760 to synchronize with the PBX, where the E1 digital stream from the provider is connected. Such business voip solutions can increase the efficiency of the entire VoIP-system.

In order to synchronize, you need to specify the sources - external lines and register configurations for Cisco to generate data on its own.

To that end, all devices and software with versions 12.4 (23) should be allocated enough, with the data to be registered in the processor, the interface, ports, and NVRAM. You should also specify the 0x101 registers, with 1760_voip # sh diag to be set in the equipment. Then you need to register port numbers and Slot modules. Further, it is important to specify the data on the WIC / VIC Slot 1, with the installation of E1 Multi-Flex Trunk WAN daughter card. At the same time, you should specify the 1.0 version and highlight the S1760_voip (config) #conft code or other options.

After you have registered the configuration, it is necessary to specify the controller type. To do this, relevant data should be entered into the interface introduced, for example, voice-port x / x: 15. After that, you should pick up and enter time slots, with controller e1 to be turned on.

GoAntiFraud offers you to start a profitable GSM termination business! If you are interested in VoIP technology, we will help you start your own business, yielding a stable income. By purchasing our comprehensive New Business package, you will start making money immediately! We will give you full technical support at all stages of business.

To refine settings, beginners often visit some specialized Voip forums. There you can find information that the command is added to adjust the system clockto ensure that the router is applied via the right interface as the priority of the clock pulses and is repeated with a different priority for the interface, the timing hierarchy, with the indication of the network clock and Clock configuration. To do this, you need to check PBX settings and make sure the router is et up with internal synchronization of the command via ISDN emulation protocol.

The 1760 device uses the commands to adjust. Data are exported when you terminate voice. For fine-tuning you should open TDM / E1 / slot / port / voice / data / line, as well as features such as: 10/100 Modular Router w / 4 slots, 19-in Chassis, 32F / 64D and V3PN Bndl w / 1760- V / 128MB DR / 32MB FL / VPN Module / 4-Ch DSP. The interface should be specified as interface Serialx / x: 15, with a group of timeslots and settings to be removed at the same time.

When the configuration is incorrect, the sound/audio playback often lacks. Also, there may be problems with the connection and the correct messaging. To test E1, you should confirm Router #.

Are you interested in VoIP technology? Are you looking for a reliable start-up in the telecommunications sector? You will be interested in the opportunity to start a GSM termination business. You can get the maximum profit making the minimal investment! We offer a turnkey GoAntiFraud solution for beginners, which includes opportunities for efficient VoIP termination, as well as a set of equipment by GoIP, EjoinTech & China Skyline at low cost.
Start UP Light - $1300
If you purchase the START UP LIGHT package, you can get equipment at wholesale prices. Read more...
Start UP - $1900
If you purchase the START UP package, you can get equipment at wholesale prices. Read more...
DeLuxe - $5600
By purchasing the DELUXE package, you get equipment at wholesale prices. Read more...
DeLuxe Plus - $6700
By purchasing the DELUXE package, you get equipment at wholesale prices. Read more...
Ultimate - $10500
You are welcome to buy the ULTIMA package and get your equipment at wholesale prices. Read more...
5334
0/5
0
votes

Get free business advice

Get Consultation

Related Articles

GoAntiFraud

Start of Work With VoIP Equipment

22 Aug 2016 15:08
Beginners, who are familiarizing with VoIP technologies, do not yet know many nuances of the organization of the Internet telephony. Some of them are willing to save and connect the Huawei 3G modem of series E1550, E160g, E173, and E1752C. But, according to experts, it is better to install the gatew...
GoAntiFraud

Is it Possible to Protect the VoIP System from Hacker Attacks?

20 Mar 2017 10:06
In recent years, more and more companies prefer to install VoIP-equipment, in order to save on telephone. However, the purchase of low-quality devices, their clumsy setup, without taking into account all the stages of protection against hacking is a direct path to the introduction of hackers into th...
GoAntiFraud

Repeaters to Amplify GSM Signals

02 Aug 2016 13:42
It is known that the terminator should provide a high quality of the route to sell it profitably. The route will be in demand among the originators only if the ACD and ASR performance are up to par. These figures describe the number of successful calls, that is, those that last for more than 0 secon...
GoAntiFraud

Efficient VoIP-telephony for a Call Center

17 Aug 2016 11:14
Some managers dream of creating their own call center. To do this, you need to expand your office and install additional telephone lines. It is known it is very expensive when you employ conventional telephony because the call center can have 100 or more lines. In this case, the best alternatives ar...
GoAntiFraud

Services of the VoIP providers as a way to save the company budget

13 May 2016 08:17
The issue of increasing the profitability of the company is acute for a senior manager. You can increase your company's revenues in two ways: Smart savings; Higher earnings. Practice shows that the cost savings can significantly increase the company’s profits. However, it is importa...
GoAntiFraud

Why Do You Need Experts to Set Up GoIP?

06 Jul 2016 11:34
Nowadays, VoIP termiantion is becoming increasingly popular among users. It's enough to install, connect and configure equipment to start working. However, after reading the information on the Internet and on the forums, many terminators try to set up the equipment on their own. A beginner usually m...
GoAntiFraud

How to Connect Several Cities via IP

16 Aug 2016 13:15
Executives of companies are successfully developing their businesses, expanding it, opening up branches in other countries and cities. And then they face a quite important question of whether to use the cloud or to set up the equipment. After all, the result of such actions should be efficient commu...
GoAntiFraud

The Main Advantages of GoIP 16

29 Sep 2016 13:28
Seasoned terminators often set up GoIP 16 and 32, while beginners usually connect 4-8-ports devices. Installation of the multichannel equipment allows earning profits efficiently and rapidly as one minute is multiplied by the number of ports in the device, in this case it is a 16-port device. Usi...

GoAntiFraud

GoAntiFraud
GoAntiFraud
GoAntiFraud
GoAntiFraud
GoAntiFraud
GoAntiFraud
GoAntiFraud
GoAntiFraud
GoAntiFraud
GoAntiFraud GoAntiFraud GoAntiFraud GoAntiFraud GoAntiFraud GoAntiFraud GoAntiFraud GoAntiFraud GoAntiFraud